International shipping Secure payment
Free shipping on orders over R1250 - courier delivery and within South Africa
A 33m roll of 50mm wide Kapton Tape. A heat resistant polyimide film commonly used as a 3D printing bed surface adhesion aid.
A 33m roll of 30mm wide Kapton Tape. A heat resistant electrically insulating polyimide film commonly used as a 3D printing bed surface adhesion aid. Rated up to 260 degrees Celcius.
33m long rolls of 200mm Kapton Tape for insulation in electronics and 3D printers – Commonly used as an adhesion surface for printing ABS plastics.
These Silicone Sock Insulators are made to keep E3D V6 Heater Blocks warm and snug, to prevent heat loss and improve part cooling capabilities.
This simple but very effective tool helps you remove prints without damaging them, with a sharp edge to get under even the squishiest squish factor.
These 300x300mm PEI Sheets are pre-applied with 3M Tape, to stick onto the top of a 3D Printer heatbed and improve first-layer adhesion - resulting in substantially better first-layer adhesion and overall printing results.
These Bulldog Clips offer 19mm of high-strength grip, often acting as semi-permanent fixtures for holding down parts like glass beds in 3D Printing.
These 220x220mm PEI Sheets are pre-applied with 3M Tape, to stick onto the top of a 3D Printer heatbed and improve first-layer adhesion - resulting in substantially better first-layer adhesion and overall printing results. Stocked to fit the Anycubic i3 Mega, TEVO Tarantula, Creality Ender 3 and Creality CR-20 3D Printers.
The Wham Bam HotBox Enclosure is one of the most convenient ways to print ABS and other tough filaments, with fold-out capabilities for easy storage.
This Anycubic BuildTak offers a 200mm diameter build surface for delta style 3D printers – Ideal as an upgrade or replacement part.
The Anycubic UltraBase offers a 310x310mm build volume that enhances print quality and convenience, while making first layer adhesion a cinch.
The Anycubic UltraBase offers a 220x220mm build volume that enhances print quality and convenience, and even includes a spare aluminium heatbed.
The Anycubic Photon FEP Film offers high-strength adhesion for DLP Printing, and is made to fit the Anycubic Photon and Photon-S DLP Printers. Comes in a convenient pack of 5 sheets.
The Wham Bam 220x220mm FBS is perfect for eliminating bed adhesion problems on the Duplicator 6, Duplicator i3, and many other popular 3D Printers.
This Creality Carborundum Glass Bed is sized 245x255mm to fit the CR-6 SE, offering great bed adhesion with a classic Ultrabase adhesion style.
The Wham Bam FBSR Double Wham is designed to offer simplified and effective dual build plates for DLP 3D Printers like the Elegoo Saturn V2.
The Wham Bam FBSR Double Wham is designed to offer simplified and effective dual build plates for DLP 3D Printers like the Creality Halot One and Creality LD-002H.
The Wham Bam FBSR Double Wham is designed to offer simplified and effective dual build plates for DLP 3D Printers like the Creality LD-002R.
A 33m roll of 25mm wide Kapton Tape. A heat resistant electrically insulating polyimide film commonly used as a 3D printing bed surface adhesion aid. Rated up to 260 degrees Celcius.
Replacement Glass Beds for CR-10S 3D Printers, offering a smooth, flat and clean surface for printing - Sourced for their impressive flatness tolerance.
These Glass Print Beds are sourced for their impressive flatness and resistance to warping, sized 320x310mm for the Creality CR-10S Pro.
If you need to replace your FEP Film on your Creality LD-002R & LD-002H DLP Printers, this handy pack of FEP Films is the perfect drop-in replacement.
The Creality Magnetic PEI FlexPlate offers the extreme capability of PEI with the convenience of the FlexPlate - for CR-20 & Ender Series 3D Printers.
The Wham Bam Slap Mat is designed to let you spill and splat your 3D Resins all you like, while offering an easy, safe way of disposing it afterwards.
Safely post process and clean your 3D Resin prints with ease when you use the extra-large 345x700mm Wham Bam Mega Silicone Slap Mat.
The Wham Bam Flexible Build System is designed with a Magnetic Base, Spring Steel Plate & PEX Build Surface for Ultimate Bed Adhesion & Convenience.
The Double Wham Bam Flexible Build System offers a Magnetic Base, Two Spring Steel Plates & Two PEX Build Surface for extremely fast turnaround times.
The Wham Bam 255x245mm FBS is the ideal bed accessory for your Creality CR-6 SE, offering excellent first-layer adhesion and ultra-easy print removal.
This awesome double-sided Wham Bam PEI Flexi Plate is 235x235mm for popular 3D Printers like the Creality Ender 3, Ender 5 and CR-20 Series.
The Wham Bam PEX Flexi Plate is preinstalled with a PEX Build Surface, making it a good drop-in upgrade or replacement for your Flexible Build System.
The Wham Bam PC Flexi Plate has a Polycarbonate Build Surface preinstalled so you can quickly swap out your FBS with absolute ease and convenience.
The Wham Bam PEX Build Surface is stocked as a replacement or spare for the Wham Bam Flexible Build System, offering high grip with easy release.
The Wham Bam PEI Build Surface is stocked as a replacement or spare for Wham Bam Bed Systems, offering BuildTak-like grip and easy flex-release.
The Wham Bam PC Build Surface is stocked as a replacement or spare for Wham Bam Bed Systems, offering BuildTak-like grip and easy flex-release.
These spare Wham Bam Magnetic Bases are perfect replacements, or can be used to equip another 3D Printer with a Wham Bam Flexible Build System.