4.3 Inch HDMI LCD 480x272 Expand

4.3 Inch HDMI LCD 480x272

Waveshare Waveshare



Small-sized Raspberry Pi or SBC 4.3 Inch Touch LCD with HDMI interface! Especially useful for those smaller embedded projects, such as adding LCD control to CNCs or 3D printers. 

More details

This product is no longer in stock

R 479.95

tax incl.

Spend R 1,250.00 more and get Free Shipping!

Free shipping on orders over R1250 - courier delivery and within South Africa


Small-sized Raspberry Pi or SBC 4.3 Inch Touch LCD with HDMI interface! Especially useful for those smaller embedded projects, such as adding LCD control to CNCs or 3D printers. 


  • 480×272 high resolution
  • Resistive touch screen control
  • Compatible and Direct-connect with any revision of Raspberry Pi (except the Pi 1 model B or Pi Zero, which requires an HDMI cable)
  • Drivers provided (Can be installed on your existing Raspbian/Ubuntu directly)
  • HDMI interface for displaying, no I/Os required (however, the touch panel still needs I/O pins)
  • Backlight can be disabled to lower power consumption


1, 17 3.3V Power positive (3.3V power input)
2, 4 5V Power positive (5V power input)
3, 5, 7, 8, 10, 11, 12, 13, 15, 16, 18, 24 NC NC
6, 9, 14, 20, 25 GND Ground
19 TP_SI SPI data input of Touch Panel
21 TP_SO SPI data output of Touch Panel
22 TP_IRQ Touch Panel interrupt, low level while the Touch Panel detects touching
23 TP_SCK SPI clock of Touch Panel
26 TP_CS Touch Panel chip selection, low active

Development Resources:

Wiki : www.waveshare.com/wiki/4.3inch_HDMI_LCD


The LCD does not work when I connect it to my Raspberry Pi / Rasbian Distro
To use the LCD with the Raspberry Pi official image, the driver must be installed first. Please refer to the user manual.
Alternatively use the provided image directly to flash your SD card. 
Also ensure that your Raspberry Pi power supply can provide enough current for the Pi and LCD
LCD does not work even when using the provided stock images. 
Check the hardware connections and cables etc. 
Ensure the SD card has flashed correctly, perhaps try a different image or card.
The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on, it is possible that the image was burnt incorrectly OR the SD card had bad contact.
Which power supply should I use?
It is strongly recommended to use a stand-alone 5V/2A power adapter (or higher than 2A current is even better), because the PC's USB port might have not enough power to support the Pi and LCD.

For more info, please check the wiki page.


No customer reviews for the moment.

Write a review

4.3 Inch HDMI LCD 480x272

4.3 Inch HDMI LCD 480x272

When it comes to producing unique electronics components and modules, there are very few brands that can provide the quality that Waveshare can. Based in the Futian District in Shenzhen, China, Waveshare are experts in developing electronics to a high standard of quality, which have been thoroughly tested to work seamlessly with corresponding development platforms and systems – such as the E-Ink HATs for Raspberry Pi’s.

What we love most about Waveshare is how they are dedicated to providing quality products, and have moved away from the typical “Made in China” stigma – cheap products with cheap parts and components. Instead, Waveshare understand the value of supplying quality products and building sustainable relationships with international resellers and distributors. They know that consistent quality will result in consistent business, and as such they always ensure strict quality control for each and every product that comes out of the manufacturing plant.

We are always excited to peruse through their vast catalogue of exciting new products to find unique modules, components or even entire development boards that are designed with quality in mind. Because we know that every cent that we spend with Waveshare will be well-spent, with each product that order adding real value to our own catalogue of products.