International shipping Secure payment
No products
Prices are tax included
Product successfully added to your shopping cart
There are 0 items in your cart. There is 1 item in your cart.
DM860H Stepper Motor Driver
HWPRDQ860H
New
The DM860H Stepper Motor Driver is first a foremost a powerful driver that is able to drive most large stepper motors.
5+ In Stock Items
Warning: Last items in stock!
Free shipping on orders over R1250 - courier delivery and within South Africa
With its pure-sine current control, quiet and smooth operation under high speeds it out performs many of the other available drivers on the market.
Features:
- High Efficiency
- Excellent high speed performance
- Max AC80V or DC110V
- Max output 7.2A
- Self-adjustment function
- Pure-sine current control
- 300KHz Max Pulse input frequence
- Suitable for TTL and optically isolated input
- Auto idle current reduction
- 16 steps resolutions in decimal binary, max 51,200 steps/rev
- Suitable for 2 ,3, 4 phases motors
- Support PUL/DIR and CW/CCW modes
- Short-voltage protection, over-voltage protection, over-current protection
M860H Stepper Motor Driver - Technical Specifications:
|
Parameters |
Min |
Typical |
Max |
|
Output Current (A) |
1.80 |
- |
7.2 (5.1 RMS) |
|
Input Voltage (VDC) |
+24 |
+68 |
+80 |
|
Logic Signal Current (mA) |
7.00 |
10 |
16 |
|
Pulse Input Frequency (KHz) |
0.00 |
- |
300 |
|
PulseWidth (Us) |
2.50 |
- |
- |
|
Pulse Voltage (VDC) |
5.00 |
- |
24 |
|
Isolation resistance (MΩ) |
500.00 |
|
|
M860H CNC Stepper Motor Driver’s Connector P1 Configurations
| Pin Function | Details |
| PUL+(+5V) | Pulse signal: In single pulse pulse/direction) mode, this input represents pulse signal, effective for each rising or falling edge (set by inside jumpers in JP1); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,effective for high level or low level (set by inside jumpers in JP1). For reliable response, pulse width should be longer than 1.5μs. Series connect resistors for current-limiting when +12V or +24V used. |
| PUL-(PUL) | |
| DIR+(+5V) | DIR signal: In single-pulse mode, this signal has low/high voltage levels,representing two directions of motor rotation; in double-pulse mode (set by inside jumper J3), this signal is counter-clock (CCW) pulse,effective for high level or low level (set by inside jumper J1). For reliable motion response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH,0-0.5V when DIR-LOW. |
| DIR-(DIR) | |
| ENA+(+5V) | Enable signal: This signal is used for enabling/disabling the driver. High level (NPN control signal, PNP and Differential control signals are on the contrary,namely Low level for enabling.) for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED). |
| ENA-(ENA) |
M860H Stepper Motor Driver’sConnector P2 Configurations
| Pin Function | Details |
| GND | DC/AC power ground |
| +V | DC/AC power supply, 20~80V, Including voltage fluctuation and EMF voltage. |
| A+,A- | Motor Phase A |
| B+,B- | Motor Phase B |
M860H Stepper Motor Driver’s Microstep and Current
The drives uses an 8 bits DIP switch to set stepper motor resolution and motor operating current, as shown below:
Dynamic Current(1/2/3) Microstep Resolution(6/7/8)
M860H Stepper Motor Driver’s Microstep Resolution Selection Standstill Current(4,Half/Full)
Microstep resolution is set by SW5, SW6, SW7, SW8 of the DIP switch as show in following:
|
Step Angle |
SW5 |
SW6 |
SW7 |
SW8 |
|
0.9 |
ON |
ON |
ON |
ON |
|
0.45 |
ON |
OFF |
ON |
ON |
|
0.225 |
ON |
ON |
OFF |
ON |
|
0.1125 |
ON |
OFF |
OFF |
ON |
|
0.05625 |
ON |
ON |
ON |
OFF |
|
0.028125 |
ON |
OFF |
ON |
OFF |
|
0.014063 |
ON |
ON |
OFF |
OFF |
|
0.007031 |
ON |
OFF |
OFF |
OFF |
|
0.36 |
OFF |
ON |
ON |
ON |
|
0.18 |
OFF |
OFF |
ON |
ON |
|
0.072 |
OFF |
ON |
OFF |
ON |
|
0.036 |
OFF |
OFF |
OFF |
ON |
|
0.0144 |
OFF |
ON |
ON |
OFF |
|
0.0072 |
OFF |
OFF |
ON |
OFF |
M860H Stepper Motor Driver’s Current Settings
The first three bits (SW1, 2, 3) of the DIP switch are used to set the dynamic current. Select a setting closest to your motor’s required current.
| Peak current (A) | RMS(A) | SW1 | SW2 | SW3 |
| 2.40 | 1.71 | on | on | on |
| 3.08 | 2.20 | off | on | on |
| 3.77 | 2.69 | on | off | on |
| 4.45 | 3.18 | off | off | on |
| 5.14 | 3.67 | on | on | off |
| 5.83 | 4.16 | off | on | off |
| 6.52 | 4.66 | on | off | off |
| 7.20 | 5.14 | off | off | off |
M860 Stepper Motor Driver’s Typical Connections
M860 Stepper Motor Driver’s Mechanical
No customer reviews for the moment.
